hitmanmcchitmanmcc
InicioConsolasCRTsSíntomasTécnicasLab

© 2026 Hitman's Museumv1.18.1

Acerca·Privacidad·Términos

Lab

Mods, experimentos y otras reparaciones

Battery compartment of a PS5 Media Remote. Both AA contact posts are crusted with green and brown corrosion, and the green circuit board shows through the translucent black housing.
+7 fotos✓Reparación exitosa

PS5 Media Remote battery corrosion cleanup

A very cheap PS5 Media Remote with leaked batteries and corroded battery contacts. After a soak in white vinegar and Evaporust, some work with a fibreglass pen and a run in the ultrasonic, it works again. The nickel plating on the contacts has seen better days.

Rust/corrosionBattery leakage damage
26 oct 20261 hilo
The old PS1 lid switch held between finger and thumb, its stem broken off, above the console's main board with its copper shielding.
+3 fotos✓Reparación exitosa

PS1 not reading discs: lid switch replacement

A PS1 that wasn't detecting discs. The stem on the lid switch had snapped off, so the console never knew the lid was closed. A new switch sorted it out.

Disc read error
22 oct 20261 hilo
The RC car's battery compartment with six green Philips AA batteries, one badly swollen and crusted in rust from leakage.
+22 fotos✓Reparación exitosa

Childhood RC car refurbishment

My brother's RC car from when we were kids, with leaked batteries that had rotted the battery contacts. I recapped and deep cleaned the controller and serviced the motor and steering gears. The original contacts were too far gone even after vinegar and Evaporust, so I replaced them with new ones. The car still wouldn't run, until it turned out the new contacts have slightly different tolerances and one battery wasn't fully seated. Pushing it all the way in brought the car back to life.

Rust/corrosionBattery leakage damage
12 oct 20261 hilo
Watchmaking tools laid out on light blue mat: open-faced watch with tan band, jeweler's screwdrivers, yellow bulb-shaped tool, precision picks, and repair supplies.
+18 fotos⏳En progreso

Watchmaking exploits

Started by changing batteries on my partner's watches, which led to acquiring more tools than the job strictly required. This will inevitably expand.

13 feb 20263 hilos
Disassembled walkie-talkie PCB held in hand showing capacitors, coils, variable resistor, and solder joints during refurbishment.
+4 fotos

Childhood Walkie Talkies refurbishment

My childhood walkie-talkies, dug out so my daughter could use them for her pretend calls. A recap, some Deoxit and a clean sorted out the reliability issues.

28 ene 20261 hilo
Disassembled white PS4 controller: the front shell at left still holds the green mainboard, with a rumble motor at the board's right edge showing orange rust; the silver lithium-ion battery and its black holder sit above, and the back shell half at right has a matching orange rust stain inside. Screwdrivers at top right.
+15 fotos✓Reparación exitosa

PS4 controller refurbishment for a friend

Two very grotty PS4 controllers, one of them drifting. The drift was fixed with nothing more than a thorough cleaning of the potentiometer wiper, and the rusted rumble motors came up reasonably well after an Evaporust soak.

Controller driftRust/corrosion
11 dic 20251 hilo
Two PSP devices on patterned fabric; upper unit shows swollen battery with broken battery door retaining clip; lower unit displays battery damage.
+1 fotos

Beware old PSP batteries (shell damage)

A swollen battery had broken the battery door's retaining clip. A new door sorted it; a good reminder to check those old aftermarket cells regularly.

Cracked/broken shellSwollen battery
3 nov 20251 hilo
The Gran Turismo UMD held label-side up (GRAN TURISMO, Polyphony Digital, PlayStation, PEGI G, UCES-01245), a crack across the clear top shell wide enough that one side sits raised above the other.
+8 fotos✓Reparación exitosa

PSP Gran Turismo "good condition" purchase refurb

Purchased as 'good condition', arrived cracked. The seller didn't want to know, so I fixed it myself. The listing photo had the damage in it all along; lesson learned.

Cracked/broken shell
24 oct 20251 hilo
Disassembled Famicom Legend of Zelda cartridge (HVC-ZL), teal shell and PCB, with a new tabbed coin-cell battery soldered on as a stopgap and a new electrolytic capacitor fitted; the removed old capacitor sits on the paper towel near the cotton swabs, with a precision screwdriver, a loose coin cell and an eraser nearby.
+7 fotos

Zelda and Super Metroid cartridge maintenance

Battery and cap replacements on Super Metroid and Zelda, with saves backed up and restored throughout. Initially used tabbed batteries as a stopgap, then swapped to coin cell holders once they arrived.

Battery-backed save loss
13 oct 20252 hilos
Disassembled game cartridges with PCBs, cleaning supplies, and tools including tweezers and pliers on work surface for maintenance.

Cartridge maintenance on a random Saturday

A few carts cleaned and serviced on a random Saturday.

11 oct 20251 hilo
Close-up of the OSSC classic board's top-right: the Altera Cyclone IV FPGA, the gold heatsink, the DC power jack and a toggle switch; the red kynar mod wire runs from a pin of the IC beneath the heatsink, through the heatsink, down to the lower-left of the board.
+16 fotos

OSSC classic modding and firmware experiments

Modded my classic OSSC to accept newer firmware, and experimented with a PC Engine-specific build that tries to emulate the composite colour palette on RGB.

22 sept 20253 hilos
Close-up of acoustic guitar fretboard and strings showing cleaned frets and polished body after restoration work.
+7 fotos

The rest of the guitar lineup

Keeping the momentum from the Yamaha job: the old acoustic and the electric got the same treatment. The old one is battered, but it was a gift from an uncle to my brother and, as such, is worth more than any of the others.

15 ago 20252 hilos
Yamaha FX370C fretboard with fret guard installed over frets during oxidation removal, strings removed for cleaning.
+17 fotos

Yamaha FX370C maintenance

Brought a used Yamaha FX370C up to a much better state with fret cleaning, lemon oil on the fretboard and a new set of strings. Was sceptical it would turn out well, but pleasantly surprised.

14 ago 20251 hilo
Disassembled Switch Pro controller showing dusty PCB board with gold contact pads and corroded internal components during cleaning maintenance.
+5 fotos

Switch Pro controller maintenance for a friend

Since I got some cheap ones for myself in Japan, a friend asked if I could import some Pro controllers for him too.

22 jul 20251 hilo
Asus PG27UQ mainboard with thermal paste applied to G-Sync module; recapping work visible on green PCB substrate.
+15 fotos⏳En progreso

Asus PG27UQ refurbishment

My personal monitor. Skimped on maintenance for too long and ended up having to replace a fan and recap the mainboard.

13 may 20252 hilos
A silver GameCube WaveBird controller on a wood floor, ringed by 14 green WavePhoenix receiver boards.
+40 fotos

WavePhoenix WaveBird receiver build

I had plenty of WaveBird controllers but only one OEM receiver, so I built a batch of loopj's open-source WavePhoenix receivers, a drop-in replacement for the GameCube WaveBird's RF dongle. Beyond the build, the threads include a full walkthrough of updating the firmware over the WavePhoenix web updater.

2 may 20256 hilos
Two Japanese Game Boy Color cartridges mid save-battery swap. The left cartridge is open, its green PCB showing a fresh tabbed CR2032 coin cell (its edge wrapped in yellow plastic) soldered in place, with the removed old tabbed cell resting beside it. The right is The Legend of Zelda: Oracle of Seasons (CGB-AZ7J-JPN) in its clear shell, and a blue spool of desoldering braid sits at the edge of frame.
+3 fotos

Game Boy cartridge maintenance

Fresh batteries in a couple of recently acquired Game Boy carts, saves backed up and restored using an Open Source Cartridge Reader.

Battery-backed save loss
22 abr 20251 hilo
Disassembled BOSS MA-12AV speaker showing exposed driver, circuit board with electrolytic capacitors, and internal wiring during refurbishment.
+22 fotos

BOSS MA-12AV speaker maintenance x2

Refurbished a pair of BOSS MA-12AV speakers for myself, then later did the same for a friend.

1 abr 20254 hilos
Close-up of black plastic gear assembly with two white gears meshed together, mounted on black housing with metal posts and mounting holes; citrus fruits blurred in background.
+6 fotos✓Reparación exitosa

Totoro toy with erratic motion

A Totoro with missing gear teeth and no matching replacement in any kit I could source. Two gears cut, filed and glued into one that works. Totoro snores happily again.

Broken gear/tooth
2 feb 20252 hilos
Hand holding a Sony cassette tape with blue pen inserted in reel, cleaning supplies and cables visible on workbench.
+8 fotos

Old cassette maintenance

Dug out some old tapes from my parents' house and cleaned them up enough to play. One of them had an album I'd recorded as a kid, a nice find.

24 nov 20242 hilos
Sony TC-FX66 stereo cassette deck showing front panel with transport controls, level meters, and Dolby indicators in working condition.
+7 fotos

Looking inside a Sony TC-FX66 tape deck

A working Sony TC-FX66 tape deck, picked up to complement the Victor. Documented the inside for the curious; it was remarkably clean in there.

13 nov 20242 hilos
Digital multimeter displaying 0.00V reading on PowerDot PCB with desoldered USB port pins visible during repair diagnostics.
+4 fotos✓Reparación exitosa

PowerDot not charging repair for a friend

A friend's PowerDot EMS device not charging. The USB port had every single pin disconnected from the board. Resoldering them was the entire fix.

Broken USB/charging port
17 oct 20241 hilo
Victor KD-A6 stereo cassette deck powered on, showing illuminated VU meters with glowing tubes and internal capacitors visible inside the chassis.
+2 fotos

Peeking inside a Victor KD-A6

A look inside the Victor KD-A6 while it's running. A lot of capacitors in there that will need attention one day.

9 oct 20241 hilo
iPod Nano and Sony MZ-N920 MiniDisc Walkman with replacement batteries and packaging on decorative fabric.
+3 fotos

iPod Nano and MiniDisc Walkman MZ-N920 refurbishment

Fresh batteries for both. The iPod's back cover was not designed with future battery replacements in mind.

5 oct 20241 hilo
Victor UX-W800 MiniDisc micro component system with illuminated display showing demo mode, featuring CD, MD, and cassette playback capabilities.
+24 fotos

Dabbling with MiniDisc

The MiniDisc rabbit hole starts here. A portable MZ-N920 in good shape, a deck that needed a new belt for its loading mechanism, and a Victor stereo that does cassette, MiniDisc and CD. An embarrassment of riches.

Broken/worn drive belt
20 sept 20245 hilos
Technician's hand holding Nvidia Shield controller PCB with newly soldered USB port replacement during testing on workbench with tools nearby.
+3 fotos✓Reparación exitosa

Nvidia Shield controller repair for a friend

USB port replacement on a friend's Nvidia Shield controller. Not a perfect cosmetic match but the footprint fits and the connection is now solid.

Broken USB/charging port
23 ago 20241 hilo
Sega 32X Virtua Racing Deluxe PCB with replaced capacitor, IPA cleaning residue, and green plastic tool on workbench.
+2 fotos✓Reparación exitosa

32X cartridge maintenance

Virtua Racing Deluxe back in action after a recap and a clean. Whether the cap was actually the cause or the IPA did the real work is unclear, but it works now.

Cartridge slot oxidation
19 feb 20241 hilo
Interior of Roland SC-88 showing NIMB C 56C06 transformer with multiple voltage taps and black wire ready for soldering to select correct input pin.

Roland SC-88 on the inside

The Roland SC-88 MIDI device has a neat party trick on the inside.

13 feb 20241 hilo
PicoCart64-lite v1.4 PCB back side showing GPIO pins, cartridge connector, and solder joints on breadboard pattern.
+9 fotos

PicoCart 64 lite

A fun little RPi Pico-based N64 flash cart. Upgraded to a Pico with 16MB flash shortly after for more headroom.

8 dic 20232 hilos
Multiple PCBs in ultrasonic cleaner basket with LED strip lighting, including green circuit boards and white component plates, mid-cleaning process.
+11 fotos

Ultrasonic cleaner first run

First outing for the ultrasonic cleaner. Started cautiously with some PCBs, then got braver with controller shells. Very satisfying to watch the crud disappear.

2 dic 20231 hilo
Hand holding green PCB with SMD components during GunCon light gun repair, black housing and red button visible below.
+5 fotos

GunCon and GunCon 2 maintenance

SMD cap replacement and a clean on both the GunCon and GunCon 2. Time Crisis and Virtua Cop passed the validation test.

14 oct 20232 hilos
Disassembled Switch Pro controller PCB with teal potentiometers exposed, tweezers visible, showing analog stick module repair work.
+2 fotos✓Reparación exitosa

Cheap Nintendo Switch Pro controllers from Japan

Six Switch Pro controllers with half of them drifting. All fixed by cleaning the potentiometers, not a single soldering iron needed.

Controller drift
23 sept 20231 hilo
Famicoun NES controller adapter PCB with exposed solder joints, yellow wiring, and repair tools on blue work mat.
+6 fotos

Famicoun NES controller adapter

Jeff Chen's Famicoun assembled and added to the collection. Now I can enjoy the Famicom from a distance.

11 ago 20231 hilo
Four Panasonic 3DO controllers with cables on wooden surface, showing refurbished condition after capacitor replacement and cleaning.
+3 fotos

3DO controller refurbishment

Two hours recapping all the 3DO controllers. Turned out to be less 'quick' than anticipated.

12 abr 20231 hilo
Three PS2VGA dongles on a wooden surface, each with a blue VGA connector, a yellow RCA composite jack (for lightgun support), a 3.5mm jack, and the metal PlayStation multi-out plug; one has a red DIP switch (SW1) and the front one has a blue VGA cable plugged into it.
+41 fotos

Jeff Chen VGA dongles

A growing collection of Jeff Chen VGA dongles assembled over time: SNES, PlayStation family, Dreamcast, Saturn and Famicom all represented. Great designs.

28 dic 20229 hilos
Two PS3 controllers disassembled on workbench: black controller with shell off revealing circuit board and components; white controller partially disassembled. Cleaning tools, small parts, and supplies visible.
✓Reparación exitosa

PS3 controller refurb

Random button presses on the black controller turned out to just be dirt. Sometimes cleaning is the fix.

Controller driftController not responding
22 nov 20221 hilo
Dreamcast arcade stick joystick assembly disassembled on workbench: cream-colored plastic housing, metal shaft, springs, washers, and screwdriver for reassembly.
+2 fotos

Dreamcast Arcade Stick maintenance

Cap replacement, cleaning and a freshly lubed joystick on the Dreamcast Arcade Stick. Marvel vs Capcom 2 confirmed operational.

21 nov 20221 hilo
Homemade FDSStick transfer cable with exposed circuit boards and connectors on workbench next to laptop displaying disk images.
+4 fotos✓Reparación exitosa

FDSStick malarkey

A homemade FDSStick transfer cable to rewrite Famicom disks that didn't match their box art. Quick lunch project.

11 nov 20222 hilos
Hand-Assembling RGB Amp Boards with Hot Air (Mega Drive & N64)
+8 fotos

Hand-Assembling RGB Amp Boards with Hot Air (Mega Drive & N64)

Three RGB amp boards assembled by hand, two Mega Drive 3BP boards and one simple N64 amp, as a first attempt at using the hot air station for most of the work instead of an iron. Pads tinned, flux applied, components placed and reflowed, with the larger parts finished by iron. The Mega Drive boards went into a PAL and an NTSC Mega Drive 2, the N64 board into an NTSC console.

25 ago 20221 hilo
Two N64 Controller Pak PCBs with F-RAM chip upgrades, loose ICs, pennies for scale, and repair tools on blue mat.
+9 fotos✓Reparación exitosa

N64 Controller Pak F-RAM Mod, Done Properly

F-RAM upgrade across a couple of N64 Controller Paks, no more batteries quietly erasing your saves. Revisited years later and redone properly, following nosIndulgences' research: the quick version can corrupt data in the long run, so this one adds a pull-up on the write-enable line.

Battery-backed save loss
18 ago 20222 hilos
Cream-colored Sega controller with colored buttons on light surface, showing retrobriting results from SG-1000 II recap repair.
+15 fotos✓Reparación exitosa

Retrobriting various retro gaming items

A batch session of retrobriting various items: SG-1000 II controllers, PC Engine shell and assorted controllers among the beneficiaries.

Yellowed shell
24 jul 20221 hilo
Close-up of repaired Logitech DiNovo Edge charging dock PCB with new barrel jack connector soldered in place, mounted on black plastic housing.
+3 fotos✓Reparación exitosa

Logitech DiNovo Edge charging dock repair

My SO accidentally tripped on the wire and sent it flying across the room, breaking the barrel jack in the process.

Broken barrel jack
11 jul 20221 hilo
N64 Rumble Pak green circuit board after repair, held in a hand. A cluster of blue Kynar jumper wires bridges the broken traces and corroded vias left by the battery leak, the solder on every component has been touched up, and the copper now looks clean and shiny with most of the corrosion gone. The black motor-driver chip sits above.
+4 fotos✓Reparación exitosa

N64 Rumble Pak necromancy

Trace repair on an N64 Rumble Pak that had suffered from leaking batteries. Short job, satisfying result.

Battery leakage damageBroken trace
20 may 20221 hilo
GameCube Jewel Polishing with Meguiar's Compounds
+4 fotos

GameCube Jewel Polishing with Meguiar's Compounds

Three GameCube jewels taken out of their consoles and run through cutting, polishing and finishing pads with the matching Meguiar's compounds, the same materials used on car paint. Not perfect, but a substantial improvement on the swirls and scratches.

9 abr 20221 hilo
Three assembled Voultar MD RGB bypass boards and four NES expansion audio enabler modules on blue surface, showing gold traces and solder joints.
+5 fotos✓Reparación exitosa

The very first mods I assembled

The very first boards I assembled: a Voultar MD RGB bypass and an NES expansion audio enabler. A steep learning curve, but you have to start somewhere.

12 jul 20212 hilos
LG TV: Failed HDMI Ports Replaced
+4 fotos✓Reparación exitosa

LG TV: Failed HDMI Ports Replaced

HDMI ports on the family LG TV failing one after the other, most likely years of cable weight stressing the joints. Both were desoldered and replaced with OEM parts, an intimidating job at the time. The parts were pricey and scarce enough that the repair was not really economical, so a complete board from a compatible but cheaper model was tracked down afterwards and kept as a spare.

Broken HDMI port
12 sept 20201 hilo