hitmanmcchitmanmcc
フィードゲーム機CRT症状テクニックLab

© 2026 Hitman's Museumv1.18.1

プロフィール·プライバシー·利用規約
ゲーム機/Sony/PlayStation

Sony

PlayStation

5件の修理ログ

Sony PS1 PU-8: Green Speckles, Reflow, Recap & xStation
+23枚✓修理成功

Sony — PlayStation

Sony PS1 PU-8: Green Speckles, Reflow, Recap & xStation

Late PU-8 PlayStation, the one that gave up its xStation to a PU-18, now getting a new xStation of its own and going to a friend. It came up with random green speckles in the video output, traced to cracked, dull solder joints on the PSU. Reflowing them and swapping two capacitors cleared it. Then a full mainboard recap, with the areas around the old capacitors treated with white vinegar and cleaned with isopropyl, the old X-Reset replaced with a cleaner one on a Consoles Unleashed QSB, and finally a full recap of the power supply as well.

Corrupted graphicsBulging capacitorsCold/dull solder joints
2026年10月6日1スレッド
Sony PS1 NTSC-J: xStation, MFO, X-Reset & Blown Fuse
+49枚✓修理成功

Sony — PlayStation

Sony PS1 NTSC-J: xStation, MFO, X-Reset & Blown Fuse

Imported NTSC-J PlayStation sent in for the full works: xStation, MFO and X-Reset installs, plus a recap and a clean. Board and PSU recaps went in without trouble, then the console came up dead, no video and no audio, once the mods were fitted. The MFO had been wired to a pad that is ground on one board revision but not on this PU-18, which shorted the 3.5V rail and blew the PS604 fuse. Rewired correctly and refitted with a fuse taken from another console, with the surrounding fuses and ferrite beads checked for further damage. Finished with a controller clean and recap, lubrication and UV protectant.

Blown fuseNo video outputNo audio
2026年7月21日1スレッド
Technician holding open Sony PS1 PAL PSU board showing capacitors, transistors, and transformer with cracked solder joints on power jack during recap repair.
+3枚

Sony — PlayStation

Sony PlayStation PAL: PSU Recap & Power Jack Reflow

Preemptive PSU recap on this Sony PlayStation PAL backup unit. The solder joints on the power jack were already starting to crack so it was only a matter of time.

Cold/dull solder joints
2023年11月25日1スレッド
Close-up of the PS1 PSU board with the big main filter cap blown and vented, its foil wrap split open. The filter cap was the only damaged component; the transformer beside it is fine and the orange PCB is undamaged. The CD drive optical pickup sits above the board.
+38枚✓修理成功

Sony — PlayStation

Sony PS1 PU-7: Magic Smoke, xStation & Switch Fix

Don't mix PSUs with incorrect mains voltages, kids. I accidentally did that on this Sony PlayStation NTSC-J in 2022, while repairing and testing the controller ports on a friend's PAL PS1. Years later, once PU-7 QSBs finally existed, it got the mod it was bought for: an xStation from a kit by Romain Brami, with DSP pins lifted, the resistor and filter by the master clock removed, three more resistors cleared from the QSB footprint, then the QSB soldered and the FFC folded up to the top side. An X-Reset QSB followed. Shortly after, the PSU turned hard to switch on, which was corrosion inside the power switch: stripped, scraped with a fiberglass pen, cleaned with isopropyl, then DeoxIT on the contacts and grease on the plunger.

PSU failureMagic smokeRust/corrosion
2022年7月4日3スレッド
Sony PlayStation PAL: Dead Controller Ports, Blown Fuse
+2枚✓修理成功

Sony — PlayStation

Sony PlayStation PAL: Dead Controller Ports, Blown Fuse

Controller ports on this PAL PlayStation had stopped working, and the fault traced to a blown fuse. It was replaced using the fuse pulled from the NTSC unit whose PSU had gone up in smoke that same evening, and a new part went into that console.

Blown fuseController not responding
2022年7月3日1スレッド