hitmanmcchitmanmcc
FeedKonsolenCRTsSymptomeTechnikenLab

© 2026 Hitman's Museumv1.18.1

Über·Datenschutz·Nutzungsbedingungen

3D-printed part

Custom 3D-printed replacement parts: transport gears, enclosures, brackets and mounts.

11 Protokolle

PC Engine CD-ROM2 internal mechanism with the laser assembly, motor, PCB and wiring on the white plastic chassis, showing the shaft where the old crumbling gear sat and where the new 3D-printed replacement gear was about to be fitted.
+18 Fotos✓Erfolgreich repariert

NEC — PC Engine CD-ROM2

NEC PC Engine CD-ROM² Restoration: Gears, Laser & Recap

This NEC PC Engine CD-ROM² threw everything at me: 3D printed gears, a dead laser, a Discman sacrifice and a spindle height mystery, before a full recap finally brought it home. Worth every frustrating hour of it.

Dead laserDisc read errorBroken drive rail/gear+1
28. Dez. 20254 Threads
Custom RGB mod enclosure mounted on Sony PVM-14L1 rear panel, showing D-sub connector, audio toggle switches, and multicolored internal wiring.
+29 Fotos✓Erfolgreich repariert

Sony — PVM-14L1

Sony PVM-14L1 Trinitron RGB Mod, Recap & Audio Fix

Helped a friend source this Sony PVM-14L1 Trinitron. RGB modded with Martin Hejnfelt's design from immerhax.com (mod PCB assembled myself), neck board reflowed and recapped, audio restored after a previous owner had disconnected the speaker.

5. Dez. 20242 Threads
Disassembled Ikegami monitor showing shattered CRT screen and internal circuit board damage from shipping transit.
+24 Fotos

Ikegami — HTM-1005RA2

Ikegami HTM-1005RA2 Broadcast Monitor: Shipping Recovery

Ikegami HTM-1005RA2 broadcast monitor acquired alongside a Victor monitor; both had one hell of a rough ride in transit. Fortunately this one fared a lot better than the Victor.

Rust/corrosion
13. Dez. 20233 Threads
Macro of the Panasonic FZ-1 mainboard's power-supply section, the area worst hit by capacitor leakage: an L4960 regulator, the silver inductor L31 (marked 101), surrounding SMD diodes and resistors, a red status LED and the Panasonic "MDFUP064" silkscreen, with the through-holes darkened and corroded from electrolyte damage.
+21 Fotos✓Erfolgreich repariert

3DO Company — Panasonic FZ-1

Panasonic FZ-1 3DO: Recap & ODE (2nd, Laser Donor)

This is the Panasonic FZ-1 3DO whose laser went to save its sibling. With the drive dead anyway, a full recap and an ODE installation was the logical conclusion.

Dead laserLeaking capacitors
4. Dez. 20234 Threads
The PC Engine AV adapter in a PointerFunction 3D-printed enclosure, its RCA outputs on the black housing (composite is carried over an RCA jack), the HuCard slot above.
+3 Fotos

NEC — PC Engine

NEC PC Engine AV Adapter in PointerFunction Enclosure

An NEC PC Engine AV adapter that came bundled with a console purchase, rehoused by PointerFunction in a custom 3D-printed enclosure finished in galaxy black.

30. Juni 20231 Thread
Black PS Vita TV on Jeff Chen 3D-printed stand, cleaned and ready for use after CFW installation and restoration.
+7 Fotos

Sony — Vita TV

Sony PS Vita TV (PCH-2000) Clean & CFW: 30€ Find

Picked up this Sony PlayStation Vita TV (PCH-2000) for 30€ with a complimentary mould smell. A good clean, a CFW install and a Jeff Chen stand later, it's a nice little unit.

18. März 20233 Threads
Close-up of Sega Nomad PCB showing removed capacitor and damaged solder joints from poor aftermarket screen installation work.
+32 Fotos✓Erfolgreich repariert

Sega — Nomad

Sega Nomad: Screen Fix + CD Audio & Master System Mods

Sega Nomad with a broken aftermarket screen, brought back to life. Plus physical mods to restore CD audio mixing and add Master System game compatibility, both omitted from the original Nomad's design.

Leaking capacitors
7. Dez. 20226 Threads
Panasonic FZ-1 motherboard with multimeter probes, solder wick, and desoldering tools during PSU trace repair and recapping restoration work.
+42 Fotos✓Erfolgreich repariert

3DO Company — Panasonic FZ-1

Panasonic FZ-1 3DO: PSU, Laser Swap & ODE (1st)

PSU repairs on this Panasonic FZ-1 3DO required bridging badly damaged traces, and a missed ceramic cap connection sent the console into a reboot loop. Sourcing a replacement laser meant buying a whole other console, but it runs now, and has since gained an ODE with SD card access through the AV expansion bay.

Dead laserPSU failureMagic smoke
16. Nov. 20226 Threads
SuperGrafx main board during refurbishment: green PCB with new capacitors, voltage regulator, and visible chip components on blue work mat.
+11 Fotos

NEC — PC Engine SuperGrafx

NEC PC Engine SuperGrafx Recap, Regulator & Jailbar Fix

Full maintenance on a NEC PC Engine SuperGrafx: a recap, a voltage regulator swap and jailbar-fix caps. Now pairs nicely with an EDFX in a mini-IFU shell.

Jailbars
5. Sept. 20222 Threads
Disassembled Panasonic Q optical drive rails laid out for comparison; one 3D printed replacement rail next to original shattered rail pieces.
+26 Fotos⏳In Arbeit

Nintendo — Panasonic Q (SL-GC10)

Panasonic Q (SL-GC10) GameCube: Drive Rails & FlippyDrive

The optical drive rails on this Panasonic Q (SL-GC10) GameCube/DVD hybrid were in pieces, so 3D-printed replacements were the first order of business. A FlippyDrive followed. Just be aware the flex cable orientation is the opposite of a regular GameCube.

Broken drive rail/gear
25. Juni 20227 Threads
Noctua replacement fan installed in Dreamcast VA1 alongside original black fan, showing copper heatsink and internal cooling modification.
+2 Fotos✓Erfolgreich repariert

Sega — Dreamcast

Sega Dreamcast VA1 PAL Noctua Fan Mod (3D-Printed Mounts)

Noctua fan mod on a PAL Sega Dreamcast VA1: fan connector adapted, mounted via a 3D-printed bracket, and 3D-printed CD door latch parts for clearance.

23. Okt. 20211 Thread