hitmanmcchitmanmcc
フィードゲーム機CRT症状テクニックLab

© 2026 Hitman's Museumv1.18.1

プロフィール·プライバシー·利用規約
CRT/Sony/PVM-6041Q

Sony — PVM-6041Q

Sony PVM-6041Q Trinitron Restoration: Recap, Reflow & Clean

2024年12月11日2スレッド約2分で読めます
Cold/dull solder joints
RecapReflow / joint reworkCRT calibration

Removed copious dust from this Sony PVM-6041Q 6-inch professional video monitor, the smallest PVM in the collection. Reflowed solder joints and recapped the neck board, deflection board and PSU.

部品・工具 (1)

240p Test Suite

Artemio Urbina's 240p Test Suite, the homebrew console test suite used to generate the on-screen test patterns shown.

hitmanmcc
hitmanmcc

2024年12月11日· スレッド1· 2件のツイート

Xで見る ↗Blueskyで見る ↗

(1/2) New arrival from Japan. A 6" PVM to add to my collection and some VGA to BNC cables that @misirajeduart.bsky.social brought to my attention. Now I have 8 cables so, 1 for each of the inputs on my Extron MVX. Does the monitor work? Find out below. #CRT #Sony #PVM

2 / 2

(2/2) Initially, only got sound, no picture. An issue with one of my SCART to BNC cables. Then I got a rolling picture, just a matter of adjusting the vertical hold knob on the back. The monitor works fine, just needs some TLC. Quality looks nice. #RETROGAMING #Castlevania #Sega

hitmanmcc
hitmanmcc

2024年12月13日· スレッド2· 7件のツイート

Xで見る ↗Blueskyで見る ↗

(1/7) A maintenance thread on my recently acquired Sony PVM-6041Q. As you can see, it's pretty dirty on the inside so besides refurbishing the PSU and neck board, I'll give it a general clean up. #Sony #PVM #CRT #restoration

2 / 7

(2/7) Started by taking out the PSU to clean up the casing, replace the old capacitors and reflow the solder joints.

3 / 7

(3/7) As can be seen the solder on the neck board was dull looking. Closer inspection revealed that at the very least, the G1 pin joint was breaking. I reflowed the joints and replaced the single electrolytic capacitor on the board.

4 / 7

(4/7) Here are some shots of it after some cleaning and reassembly.

5 / 7

(5/7) At this point in time I went to test it and it would not power on, much to my dismay. After swapping it with the PSU on one of my 9" PVMs it worked fine and so did the 9" PVM with this PSU so, long story short, I got trolled by some connector that I ended up reseating.

6 / 7

(6/7) Finally, what were here for, some testing with RGB on the #Sega Nomad, playing Rocket Knight Adventures. #RETROGAMING

7 / 7

(7/7) To round off testing, some shots taken while playing Columns on the Wondermega using composite. #RETROGAMING #Columns

関連する修理

Sony PVM-9041Q B board (top side) with the new colour trimmer pots fitted and the old orange ones removed onto the white paper towel below, a metal shield over part of the board. This is the B board, not the PSU.

Sony — PVM-9041Q

Sony PVM-9041Q Trinitron: PSU, Trim Pots & Deflection

Finger pointing to reflowed solder joint on Sony BVM neckboard, showing repaired connection that caused color loss.

Sony — BVM-9045QD

Sony BVM-9045QD: Neckboard Joint Fix & Full Recap

Sony PVM-9040 CRT displaying color bars test pattern showing RED, GREEN, BLUE, and WHITE channels for diagnostics.

Sony — PVM-9040

Sony PVM-9040 Triplets: Trim Pots Fix B&W Issue

Sony CPD-G420 running Castlevania Chronicles at Stage 07 with severe geometry distortion, the image sheared into a skewed parallelogram, before the G2 calibration fix.

Sony — CPD-G420

Sony CPD-G420 FD Trinitron: WinDAS G2 Calibration

The restored Sony PVM-9045QD on the black BlueShell3D 3D-printed stand, three-quarter view, its screen showing a paused game of Ristar on a jungle level.

Sony — PVM-9045QD

Sony PVM-9045QD Trinitron: PSU, Neck & Deflection

Sony PVM-14M4J displaying color bars test pattern showing red, green, and yellow bars with missing blue channel output during repair diagnostics.

Sony — PVM-14M4J

Sony PVM-14M4J Trinitron: Retrace Lines & Colour Fix